Detaylı Arama
İptal
Bulunan: 5 Adet 0.001 sn
- Eklemek veya çıkarmak istediğiniz kriterleriniz için 'Dahil' / 'Hariç' seçeneğini kullanabilirsiniz. Sorgu satırları birbirine 'VE' bağlacı ile bağlıdır.
- İptal tuşuna basarak normal aramaya dönebilirsiniz.
Filtreler
Filtreler
Bulunan: 5 Adet 0.001 sn
Yayın Dili : en ✕Konu Başlıkları : Grain Refinement ✕
Koleksiyon [3]
Ambargo Durumu [1]
Tam Metin [1]
Yayın Türü [1]
Yazar/lar [7]
Atıf Dizini [3]
Konu Başlıkları [14]
Yayıncı [4]
Yayın Tarihi [3]
Yayın Dili [1]
Erişime Açık

Observation of Hot Tearing in Sr-B Modified A356 Alloy

ULUDAĞ, Muhammet | ÇETİN, Remzi | DIŞPINAR, Derya.

In this work, T-shaped mould design was used to generate hot spot and the effect of Sr and B on the hot tearing susceptibility of A356 was investigated. The die temperature was kept at 250°C and the pouring was carried out at 740°C. The amonut of Sr and B additions were 30 and 10 ppm, respectively. One of the most important defects that may exist in cast aluminium is the presence of bifilms. Bifilms can form by the surface turbulence of liquid metal. During such an action, two unbonded surfaces of oxides fold over each other which act as a crack. Therefore, this defect cause many problems in t ...Daha fazlası

Makale 2017 De Gruyter Open Ltd 4 Görüntülenme
Erişime Açık

The effects of degassing, grain refinement & Sr-addition on melt quality-hot tear sensitivity relationships in cast A380 aluminum alloy

ULUDAĞ, Muhammet | ÇETİN, Remzi | DIŞPINAR, Derya | TİRYAKİOĞLU, Murat

Hot tearing tendency of A380 with various element additions (Sr, Sr+Ti, Ti, B and B+Sr) was investigated. Constrained rod casting (CRC) hot tearing test method was used to characterize the hot tearing sensitivity. Reduced pressure test (RPT) samples were produced from each condition and all trials were repeated three times. Number density of pores on the cross section of RPT samples was calculated via digital image processing and statistical analysis was carried out. Microstructure analysis was carried out to observe the effect of alloying elements. Hot torn cross sections were subjected to SE ...Daha fazlası

Makale 2018 Elsevier Ltd 3 Görüntülenme
Erişime Açık

Effect of Sr and Ti Addition on the Corrosion Behavior of Al-7Si-0.3Mg Alloy

ÇETİN, Remzi | ULUDAĞ, Muhammet | KOÇABAŞ, Mustafa | DIŞPINAR, Derya | CANSEVER, Nurhan

In the present study, the corrosion behaviour of A356 (Al-7Si-0.3Mg) alloy in 3.5% NaCl solution has been evaluated using cyclic/potentiodynamic polarization tests. The alloy was provided in the unmodified form and it was then modified with AlTi5B1 for grain refinement and with AlSr15 for Si modifications. These modifications yield to better mechanical properties. Tensile tests were performed. In addition, bifilm index and SDAS values were calculated and microstructure of the samples was investigated. As a result of the corrosion test, the Ecorr values for all conditions were determined approx ...Daha fazlası

Makale 2017 Archives of Foundry Engineering 3 Görüntülenme
Erişime Açık

Characterization of the Effect of Melt Treatments on Melt Quality in Al-7wt %Si-Mg Alloys

ÇETİN, Remzi | ULUDAĞ, Muhammet | DIŞPINAR, Derya | TİRYAKİOĞLU, Murat

The effects of degassing, holding time and melt additions (Sr, Sr + Ti, Ti, B and B + Sr) on the quality of A356 melts were examined. A total of 120 reduced pressure test samples were collected. Pores in these samples were analyzed via digital image processing to determine the number density of pores as well as the statistical distribution of their sizes. Results showed that in all cases, degassing with argon reduced the number of defects regardless of the additions made to the melts. Moreover, all additions were found to degrade melt quality. The lowest number density of pores in all melts wa ...Daha fazlası

Makale 2017 METALS 6 Görüntülenme
Erişime Açık

Grain Refinement, Modification, Degassing and Melt Quality Relationship in Al-7Si-0.3Mg

ÇETİN, Remzi | ULUDAĞ, Muhammet | DIŞPINAR, Derya

In this work, Al-7Si-0.3Mg alloy was studied. The alloy conditions was selected to be as-received, AlB3 grain refined and Sr modified. For each parameter, castings were made before and after degassing. In order to quantify the melt quality, reduced pressure test was used and bifilm index measurements were made. All the cast parts were subjected to metallographical examination, and thus, porosity measurements, distribution, area fraction were compared for each of the casting conditions.

Makale 2014 5 Görüntülenme
6698 sayılı Kişisel Verilerin Korunması Kanunu kapsamında yükümlülüklerimiz ve cerez politikamız hakkında bilgi sahibi olmak için alttaki bağlantıyı kullanabilirsiniz.
Tamam Açık Erişim PolitikasıAçık Erişim Yönergesi
creativecommons
Bu site altında yer alan tüm kaynaklar Creative Commons Alıntı-GayriTicari-Türetilemez 4.0 Uluslararası Lisansı ile lisanslanmıştır.
Platforms